February 2025 update - moving the "furniture"

 Rearranged the 'furniture.'

Up to now, I've been using a lot of power strips to accommodate all the electrical plugins I have. Some at the rear wall for the power and Movie hdd bank. The HDDs were moved up to the TV. I removed the hdd shelf on the back wall and relocated the shelf just below the TV, accessible but not intrusive.I removed the two pieces of clapboard and replaced them with the plywood sheet that was holding the turntable over the AVR.

The turntable has been removed to the top of the right Altec speaker cabinet. A center speaker module sits on top of the AVR. A blueray player sits on top of the left Altec cabinet.

The three 3.5" sata drives and the 2.5" drives ,and their hub ,are now on the shelf. 

I updated the Plex and Jellyfin software.

The Senhneiser WiFi headphones are working but I removed the circuit board when the unit became intermittent and finally seemed to die. Removed from the plastic housing, the unit works acceptably, though the plugin to the laptop audio output jack is still a nuisance. 

A SDR with or without an ESP32 or ESP8266, may be capable of replacing that wired connecion with a WiFi connection. A stereo FM transceiver is needed. to send the signal from the laptop audio out to the headphone audio in.


Bottom line: I can now operate everything from my seat.



Comments

Post a Comment

Popular posts from this blog

Drive rack, ventilation and wiring.

 My drives have a new rack to hold them. Hot glue and square wood dowels provided the materials with which to build the rack. I used zip ties and a small computer fan attached to the end of the rack to provide cooling air ventilation for the drives. This will increase the lifetime of the drives. Previously the were stacked on top of each other and became noticeably warm during use. The wiring really was bad. Too many cables/wires held together with zip ties. I added a surge protected outlet strip of a newer, more sophisticated design. I rearranged the system wiring to minimize the number of outlet strips and the disarrayed wires. Two strips were screwed to the wall. One was removed. The circular strip was moved from the entertainment center to a work table beside the other two strips and combined with them to supply all devices attached to the system. The strip removed replaced the circular strip in the entertainment system.  Overall, the current setup works better. Both syste...
Read more

Jellyfin media server

 The owner of Emby has blocked my using the WebOS access method of using Emby. I discovered the method and posted on the product's forum. That software is no longer my media server and has been removed from my computers. I replaced Emby with Jellyfin. Jellyfin is the evolved Emby open sourced. Emby was originally open source (and free) but was privatized and monetized by the creator. Many considered that move unethical.  The last open source version became the basis for Jellyfin,  easily competitive with Emby and almost, if not equally, well known. I've been using Jellyfin for about a year, perhaps more. The software has issues but is in constant development but is very useful in the current state, version 10.8.5.
Read more

Philips Hue lights Updated

 Philips Hue lights are known for the ability to program brightness, saturation, and hue using software. Most people use one or more cellphone apps to control their Hue lights. I've a history in computrer science and electronic technology and engineering, so took this up as a new interest. WiFi control of light bulbs' colors has interested me ever since I read aboout the topic some years ago. There happened to be seven Hue bulbs available from one eBay seller and for a reaosnable fee, approximately $20. A bridge device is used to communicate with the bulbs, so I waited for a good deal on eBay and got one. Philips has evolved a developer community and resources for those who want to explore the possibilities in lamp light control. The user joins the communnity and gets a temporary API key, formerly referred to as a 'username', good for one session. Then a browser or app, can be used to send commands to the bulbs. There are other avenues of communication. Python libraries...
Read more